Flower Rod40 cm long x 2 mm diameter *You can use bamboo skewers or balloon holder as an alternative materials
Iron wire40cmx0.7mm
Fiber fill/stuffing
Instructions
Flower(make 2)
R1: start work 6 sc in magic ring with green yarn, 1 ss, 1 chR2: 6 sc, 1 ssR3: work front loops only (FLO): ( 5 ch, Insert your hook behind the first stitches vertical bar in the chain below: 4 ss, 1 ss to the next front loop st ) * 6 times.
Change to blue yarn (Petals)R4: work back loops only(BLO): ( 2 ch, 2 sc in next st, 2 sc) * 2 times.R5: turn your work, [( 8 ch, Insert your hook behind the first stitches vertical bar in the chain below: 8 Afghan sc, 2 ch, Insert your hook behind the second stitches vertical bar in the chain below:, 1ss, 5 Afghan sc, 2 ch, from 2nd st of hook, 1 ss, 1 ch, 7 sc), 1 ss in next st]* 8 times.
Flower bud
Start with a magic ringR1: 2 ch, 12 dc in the round, 1 ss, 1 ch [12]R2-3: work 12 sc, 1 ss, 1 ch [12]R4: (sc2tog) * 6 times [6]sew around with a darning needle and close the loop.*Fill it with stuffing inside
Sepals of flower bud
R1: start with 6 sc in the magic ring, 1 ssR2: ( 6 ch, Insert your hook behind the first stitches vertical bar in the chain below: 5 ss ) * 6 times, 1 ss, 1 ch. cut and leave a tail
Big leaf (make 2)
( 13 ch, Insert your hook behind the first stitches vertical bar in the chain below: 13 ss ) * 2 times,10 ch, Insert your hook behind the first stitches vertical bar in the chain below: 10 ss. cut and leave a tail.
Small leaf ( make 3 )
( 10 ch, Insert your hook behind the first stitches vertical bar in the chain below: 10 ss ) * 2 times,7 ch, Insert your hook behind the first stitches vertical bar in the chain below: 7 ss. cut and leave a tail
Flower core(make 2)
Step 1: Prepare two pieces of 40cmx0.7mm iron wires.Step 2: Wrap cream yarn around your fingers 20 circles, take a piece of iron wire through the loops, fold it in half, and tighten it.Step 3: Take another wire through the opposite loops, fold it in half, and tighten it.Step 4: Use scissors to cut in the middle of the loops, which is two flower cores.
Assemble
In order for you to assemble Wild flower, you must have these parts and materials:2 flowers1 Flower budSepals of flower bud2 big leaves3 small leaves2 cream flower coreflower rodhit melt adhesiveiron wire
Putting all together
1. For the flowers, insert the cream flower core into the middle of the flower, tighten it, trim the flower core, keep the length of 1.2cm, and trim out the arc.2. Wrap a green yarn on the iron wire and insert 1 big leaf in the middle of the stem and continue on wrapping around. Don’t forget to secure the end part with hot melt adhesive.3. Repeat the same process for the 2nd flower but instead of using big leaf, use a small leaf.4. For the flower bud, coil the top end part of the iron wire and insert it in middle of the sepals. Secure it with hot melt glue5. Attach the flower bud on the sepals6. Linked in the flower rod and the stem of the flower bud together. Wrap it with green yarn.7. Insert 1 small leaf and continue on wrapping green yarn around the rod.8. Attach the 1st flower with a small leaf on the rod and secure it with wrapping green yarn on it9. Insert 1 small leaf, wrap a green yarn, and attach the 2nd flower with a big leaf10. Continue wrapping and attach the last big leaf and wrap the stem with green leaf and secure the end point with the hot melt adhesive
Video
Notes
Our pattern is written in US crochet terms.
Follow the counting and instructions carefully in this pattern.
Take note of the special stitches and techniques each round.
Video tutorials are available for additional guidance.
Video subtitles need to be turned on by yourself in the settings.